https://demos.peachfinthemes.com/circuit-works Wed, 23 Sep 2026 02:47:34 +0000 en-US hourly 1 https://wordpress.org/?v=7.1.1 https://demos.peachfinthemes.com/circuit-works/circuit-works-gripper-below-a-camera/ Wed, 23 Sep 2026 02:47:34 +0000 https://demos.peachfinthemes.com/circuit-works/circuit-works-gripper-below-a-camera/ Seen from above, the gripper hangs over a white mat scattered with small wooden cubes printed with black-and-white square markers. The photograph is sharp at the jaws and softer towards the background, so this sheet stays with the hardware in focus.

Callouts

1. Two toothed gears mesh at the top of the gripper, so the two jaws appear to be geared to move together.
2. Each finger hangs from a pair of linkage arms; a screw marks every pivot.
3. Both fingertips are covered by soft black caps.
4. A camera module with a round lens is fixed to the blue frame above the gripper.
5. A black cable loops from the gripper back towards the frame.

Bill of materials (as seen)

Part	Qty	Note
Gripper fingers	2	Capped tips
Meshing gears	2	Top of the gripper
Camera module	1	Round lens, facing down
Blue frame	1	Holds the camera
Cable	1	Loops back to the frame

Revisions

Rev A · 18 Aug 2026 · First look

Recorded the gears and the two fingers. The drive is left unstated: it is not visible in the photograph.

Rev B · 2 Sep 2026 · Linkages

Added the linkage arms and pivots after a closer look at the screw heads. The marker cubes are noted as background, not part of the build.

]]> https://demos.peachfinthemes.com/circuit-works/circuit-works-corner-of-a-green-board/ Tue, 22 Sep 2026 02:47:34 +0000 https://demos.peachfinthemes.com/circuit-works/circuit-works-corner-of-a-green-board/ The board is held at an angle above a dark workspace, with loose screws resting below and a laptop keyboard at the edge of the frame. Printed values are visible on several parts; this sheet does not rely on them.

Callouts

1. A blue multi-pin connector with a metal housing runs along the left edge.
2. Cylindrical capacitors stand in a loose cluster near the corner.
3. A small red switch sits beside a black socket.
4. A large square chip is visible towards the top right, out of focus.
5. Brown residue surrounds the corner mounting hole.

Bill of materials (as seen)

Part	Qty	Note
Blue edge connector	1	Left edge
Cylindrical capacitors	Several	Near the corner
Red switch	1	Beside the black socket
Square chip	1	Top right, soft focus
Loose screws	Several	Below the board, not fitted

Revisions

Rev A · 12 Aug 2026 · First look

Listed the edge connector and the capacitor cluster.

Rev B · 26 Aug 2026 · Corner detail

Added the residue around the mounting hole. Its cause is not stated; the photograph does not show it.

]]> https://demos.peachfinthemes.com/circuit-works/circuit-works-five-memory-modules/ Mon, 21 Sep 2026 02:47:35 +0000 https://demos.peachfinthemes.com/circuit-works/circuit-works-five-memory-modules/ The modules are lined up on a plain white surface and photographed from a low angle, so the nearest two are sharp and the back three soften. Capacity and speed are not stated anywhere on this sheet: the photograph does not settle them.

Callouts

1. Five modules lie parallel, evenly spaced.
2. Each shows four black chips on its visible side.
3. Gold edge contacts run the full length of each module.
4. The notch in the contacts sits off-centre.
5. Small components line the board between and around the chips.

Bill of materials (as seen)

Part	Qty	Note
Memory modules	5	Laptop size
Chips per visible side	4	Black packages
Edge notches	1 each	Off-centre

Revisions

Rev A · 5 Aug 2026 · First look

Counted the modules and the chips on each.

Rev B · 20 Aug 2026 · Focus note

Added that only the nearest two modules are sharp, so later notes stay with those two.

]]> https://demos.peachfinthemes.com/circuit-works/circuit-works-print-head-over-an-empty-plate/ Sun, 20 Sep 2026 02:47:35 +0000 https://demos.peachfinthemes.com/circuit-works/circuit-works-print-head-over-an-empty-plate/ The printer is photographed at plate level with nothing on the plate. Manufacturer labels are visible on the machine; this study is about the arrangement of parts, not the brand, and implies no endorsement.

Callouts

1. The print head carries a round fan grille on its face and a smaller blower beside it.
2. A warning label sits on the lower corner of the print head.
3. Black aluminium rails form the frame and the gantry.
4. A printed circular outline marks the plate.
5. Large knurled knobs sit under the corners of the plate.

Bill of materials (as seen)

Part	Qty	Note
Print head	1	Parked left of centre
Fans	2	Round grille and blower
Build plate	1	Empty
Levelling knobs	2 visible	Under the plate

Revisions

Rev A · 29 Jul 2026 · First look

Recorded the print head, fans and plate.

Rev B · 14 Aug 2026 · Frame

Added the rails and knobs. Print quality is not assessed; nothing is being printed in the photograph.

]]> https://demos.peachfinthemes.com/circuit-works/circuit-works-cracked-disc-fault-study/ Sat, 19 Sep 2026 02:47:35 +0000 https://demos.peachfinthemes.com/circuit-works/circuit-works-cracked-disc-fault-study/ This is a fault observation. The blue disc has a dark crack running across its face. The photograph does not show what caused it, whether the board still works, or what might replace the part, so the sheet records none of those.

Callouts

1. A dark crack runs across the face of the blue disc.
2. Two red wires rise from the board on either side of it.
3. White adhesive holds nearby parts in place.
4. A large black cylindrical capacitor sits in the foreground.
5. A grey cable loops around the board.

Bill of materials (as seen)

Part	Qty	Note
Blue disc component	1	Cracked
Red wires	2	Either side of the disc
Black cylindrical capacitor	1	Foreground
Blue cylindrical capacitor	1	Upper left

Revisions

Rev A · 22 Jul 2026 · Fault noted

Recorded the crack and its position on the board.

Rev B · 6 Aug 2026 · Scope

Removed a guess about the cause. The sheet now records only what the photograph shows.

]]>